Update 2016-01-09: In the previous version, I never added the command for creating the array and since I needed it for a new server. When the array starts rebuilding, it will look like there is a failed drive: this is normal. When it builds from scratch, it is actually doing the rebuild process and will indicate a failed drive until the array is rebuilt.
# mdadm --create --verbose /dev/md0 --level=5 --raid-devices=3 /dev/sdb1 /dev/sdc1 /dev/sdd1
# cat /proc/mdstat
md0 : active raid5 sdd1[3] sdc1[1] sdb1[0]
4294702080 blocks super 1.2 level 5, 512k chunk, algorithm 2 [3/2] [UU_]
[====>................] recovery = 20.1% (433131624/2147351040) finish=420.1min speed=68006K/sec
As you can see from the above, this isn’t very fast. I found this article with some tips on increasing the speed. The one that worked for me was increasing the stripe-cache_size (tip 3):
# echo 32768 > /sys/block/md0/md/stripe_cache_size
md0 : active raid5 sdd1[3] sdc1[1] sdb1[0]
4294702080 blocks super 1.2 level 5, 512k chunk, algorithm 2 [3/2] [UU_]
[====>................] recovery = 24.3% (523330980/2147351040) finish=147.1min speed=183976K/sec
Much better, about 3x faster.
Original With all the load shedding, a drive failed in my software raid array. It is a Raid-5 setup, so I had time to replace the drive and rebuild the array. I was lucky with this failure as I randomly looked at my mdadm array today - I really need to set up the mail details to allow the system to mail me when something fails. Here is the command to check the health of your arrays:
cat /proc/mdstat
Personalities : [raid6] [raid5] [raid4] [linear] [multipath] [raid0] [raid1] [raid10]
md0 : active raid5 sdc1[2] sda1[0] sdb1[1]
2929890816 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/3] [UUU_]
unused devices: <none>
Replacing the broken drive
The [UUU_] indicates that one of the drives is no longer part of the array. To see which drive is faulty, run mdadm --detail /dev/md0 to get the details:
/dev/md0:
Version : 1.2
Creation Time : Mon Jun 23 20:08:17 2014
Raid Level : raid5
Array Size : 2929890816 (2794.16 GiB 3000.21 GB)
Used Dev Size : 976630272 (931.39 GiB 1000.07 GB)
Raid Devices : 4
Total Devices : 3
Persistence : Superblock is persistent
Update Time : Fri Feb 17 08:24:12 2015
State : clean, degraded
Active Devices : 3
Working Devices : 3
Failed Devices : 0
Spare Devices : 0
Layout : left-symmetric
Chunk Size : 512K
Name : Token:0 (local to host Token)
UUID : 0b9ec9a1:73b38783:7bccad64:04b10ed8
Events : 758663
Number Major Minor RaidDevice State
0 8 1 0 active sync /dev/sda1
1 8 17 1 active sync /dev/sdb1
2 8 33 2 active sync /dev/sdc1
4 0 0 3 removed
This indicated that the last drive /dev/sdd1 was missing. To figure out which drive this is, you can grab the serial number using SmartMontools
sudo apt-get install smartmontools
smartctl -a /dev/sdd | grep Serial
Serial Number: 3NX12345
Time to open up the server and find the faulty drive. My server has hot swap bays and I guessed ‘sdd’ to be the fourth drive, so got the right one on my first attempt. Replaced the drive with a spare I had - originally I ran a 8x 1TB Raid-5 array on a different server, but the power usage was too high, so scaled things down a bit. To get the backup drive correctly partitioned, I deleted all the existing partitions and added a new one with file-system type ‘fd’ for ‘Linux Raid autodetect’ using fdisk. To add the disk back into the array, use mdadm --manage /dev/md0 --add /dev/sdd1. To check the progress, look at /proc/mdstat:
cat /proc/mdstat
Personalities : [raid6] [raid5] [raid4] [linear] [multipath] [raid0] [raid1] [raid10]
md0 : active raid5 sdd1[4] sdc1[2] sda1[0] sdb1[1]
2929890816 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/3] [UUU_]
[>....................] recovery = 0.0% (190080/976630272) finish=256.8min speed=63360K/sec
unused devices: <none>
All good, now just need to wait till the rebuild is complete. It is advisable to stop all processes / applications during this period to speed up the rebuild. In my case, stopping XMBC increased the speed by 10x. Once the rebuild is complete, you should see something like this:
cat /proc/mdstat
Personalities : [raid6] [raid5] [raid4] [linear] [multipath] [raid0] [raid1] [raid10]
md0 : active raid5 sdd1[4] sdc1[2] sda1[0] sdb1[1]
2929890816 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/4] [UUUU]
unused devices: <none>
Notifications for future failures
Now to ensure we get notified about any future fails, we need to set up mailing. I found this post which looked to be what I needed. Here is the short version:
sudo apt-get install msmtp msmtp-mta
To find the global configuration file, use msmtp --version | grep "System configuration":
System configuration file name: /etc/msmtprc
Edit the file with sudo vi /etc/msmtprc and add (remember to replace with your specific details and also to enable SMTP on your GMail account):
# ------------------------------------------------------------------------------
# msmtp System Wide Configuration file
# ------------------------------------------------------------------------------
# A system wide configuration is optional.
# If it exists, it usually defines a default account.
# This allows msmtp to be used like /usr/sbin/sendmail.
# ------------------------------------------------------------------------------
# Accounts
# ------------------------------------------------------------------------------
# gmail account
# Configuring for gmail is beyond the scope of this tutorial
# Googling for "gmail msmtp" should help
account gmail
host smtp.gmail.com
port 587
from youremail@gmail.com
tls on
tls_starttls on
tls_trust_file /etc/ssl/certs/ca-certificates.crt
auth on
user youremail
password supersecret
syslog LOG_MAIL
# Other ISP Account
# Configuring for other ISPs is beyond the scope of this tutorial
# Googling for "myisp outlook smtp" should help
# ------------------------------------------------------------------------------
# Configurations
# ------------------------------------------------------------------------------
# Construct envelope-from addresses of the form "user@oursite.example".
#auto_from on
#maildomain fermmy.server
# Use TLS.
#tls on
#tls_trust_file /etc/ssl/certs/ca-certificates.crt
# Syslog logging with facility LOG_MAIL instead of the default LOG_USER.
# Must be done within "account" sub-section above
#syslog LOG_MAIL
# Set a default account
account default : gmail
# ------------------------------------------------------------------------------
To test, run echo "This is a test e-mail from my server using msmtp" | msmtp -d youremail@gmail.com. It should print out multiple lines, any error will be clearly displayed as such, i.e.
--> AUTH PLAIN AGNvYnVzYXyXbmFyZGuYYmthdnFiam9seXZlaGJiZA==
<-- 535-5.7.8 Username and Password not accepted. Learn more at
<-- 535 5.7.8 http://support.google.com/mail/bin/answer.py?answer=14257 n1sm2519061wib.11 - gsmtp
msmtp: authentication failed (method PLAIN)
msmtp: server message: 535-5.7.8 Username and Password not accepted. Learn more at
msmtp: server message: 535 5.7.8 http://support.google.com/mail/bin/answer.py?answer=14257 n1sm2519061wib.11 - gsmtp
msmtp: could not send mail (account default from /etc/msmtprc)
Now to replace the sendmail command with msmtp:
sudo mv /usr/sbin/sendmail /usr/sbin/sendmail.bak
sudo ln -s /usr/bin/msmtp /usr/sbin/sendmail
Add these lines to you /etc/mdadm/mdadm.conf file:
# instruct the monitoring daemon where to send mail alerts
MAILADDR youremail@domain.com
MAILFROM my-server-name - mdadm
Then to test, use sudo mdadm --monitor --scan --test --oneshot. If all is set up correctly, you should get a mail like this:
This is an automatically generated mail message from mdadm
running on Token
A SparesMissing event had been detected on md device /dev/md0.
Faithfully yours, etc.
P.S. The /proc/mdstat file currently contains the following:
Personalities : [raid6] [raid5] [raid4] [linear] [multipath] [raid0] [raid1] [raid10]
md0 : active raid5 sdc1[2] sdb1[1] sda1[0] sdd1[4]
2929890816 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/4] [UUUU]
unused devices: <none>
So after all that, you should be notified when something goes wrong and be able to correct it before loosing all your data.
